Binky has tested a lot of coatings. Nitrile keeps showing up at the top. Here's why.
If you work with your hands in wet, oily, or dry conditions — and most operators do all three in the same shift — nitrile is the coating that doesn't make you choose. It grips in oil. It grips in water. It grips dry. It resists chemicals, abrasion, and punctures. Binky has run nitrile-coated gloves across industrial, mechanical, and precision work environments. The verdict is consistent: nitrile earns its place.
What Nitrile Actually Does
Nitrile is a synthetic rubber coating applied to the palm and fingers of a glove shell. Unlike latex, it's allergy-safe. Unlike PU, it handles wet and oily conditions without losing grip. Unlike bare leather, it adds a chemical and abrasion-resistant barrier that extends the life of the glove and the hands inside it.
Binky's breakdown of what nitrile delivers:
- Wet grip — nitrile maintains traction on wet surfaces where other coatings slip. Critical for outdoor work, wet manufacturing, and any environment where water is present.
- Oil resistance — nitrile doesn't degrade in oil and maintains grip on oily parts and tools. Binky's go-to for mechanical and automotive work.
- Chemical resistance — resistant to a wide range of solvents, oils, and industrial chemicals. Adds a protective barrier between the hand and the hazard.
- Abrasion resistance — nitrile foam and sandy-finish nitrile add texture that resists wear and extends glove life in high-friction applications.
- Puncture resistance — especially in foam nitrile configurations, the coating adds a meaningful layer of puncture protection over the shell.
Binky's Nitrile Pick #1: MCR Kevlar Gloves 9178NF — Kevlar/Nitrile Foam
The MCR 9178NF is Binky's heavy-duty nitrile pick. Kevlar shell for cut resistance. Nitrile foam coating for grip, puncture resistance, and chemical protection. Black finish. Available in Large and X-Large for operators who need a proper fit at the higher end of the size range.
The Kevlar/nitrile foam combination is what Binky respects here — the shell handles cut hazards while the coating handles grip and chemical exposure simultaneously. One glove, multiple hazard categories covered. That's the kind of efficiency Binky appreciates.
- Kevlar shell — cut resistance built into the foundation
- Nitrile foam coating — grip, puncture resistance, chemical protection
- Black finish — professional appearance that holds up through use
- Available in Large and X-Large — proper sizing for larger operators
"Kevlar cuts the cut risk. Nitrile handles everything else. Binky calls that a complete glove." — Binky
Binky's Nitrile Pick #2: Task Gloves TSK2006 — 13 Gauge Polyester Knit, Nitrile Coated
The TSK2006 is Binky's precision and general-purpose nitrile pick. 13-gauge polyester knit shell gives the dexterity and breathability that heavier shells can't match. Nitrile coating on the palm and fingers delivers grip and protection without adding bulk. The result is a lightweight, highly dexterous glove that still performs in wet and oily conditions.
Binky reaches for the TSK2006 when the work requires feel — assembly, parts handling, light manufacturing, and any application where the hands need to move fast and accurately. The nitrile coating keeps grip consistent without sacrificing the tactility the 13-gauge knit provides.
- 13-gauge polyester knit shell — lightweight, breathable, high dexterity
- Nitrile palm coating — grip and protection without bulk
- Wet and oily condition performance — consistent grip across conditions
- General-purpose versatility — assembly, parts handling, light manufacturing
"Light enough to feel everything. Coated enough to grip anything. Binky uses these more than he expected to." — Binky
Binky's Nitrile Pick #3: Ultra-Thin Cut Level A2 Work Gloves (12-Pack)
When the operation runs at volume and cut protection is the baseline requirement, Binky goes to the Ultra-Thin A2 12-pack. ANSI A2 cut resistance in an ultra-thin construction that doesn't sacrifice dexterity for protection. The 12-pack format is the detail Binky respects — serious operations go through gloves, and having a full rotation ready means the hands are always protected, never waiting on a reorder.
Nitrile coating delivers the grip performance the A2 shell needs to be useful in real working conditions. Cut protection without grip is half a solution. Binky doesn't do half solutions.
- ANSI A2 cut resistance — protection against sheet metal, glass, and sharp edges
- Ultra-thin construction — dexterity preserved at the cut-resistant level
- Nitrile coating — grip in wet, dry, and oily conditions
- 12-pack format — built for teams and operators who maintain a proper rotation
"A2 protection. Ultra-thin feel. 12 pairs deep. Binky calls that operational readiness." — Binky
The Bottom Line on Nitrile
Wet grip. Oil resistance. Chemical protection. Abrasion resistance. Nitrile delivers all four without asking you to compromise on dexterity or comfort. Whether it's paired with a Kevlar shell for cut hazards, a 13-gauge knit for precision work, or an ultra-thin A2 construction for high-volume operations — nitrile is the coating that shows up in every environment Binky works in.
Shop all nitrile-coated gloves at WetGloves.com — Binky-certified for every condition.
"Nitrile doesn't pick favorites between wet, dry, and oily. Neither does Binky. That's the alignment." — Binky. WetGloves.com
0 comments